2024 NDS / 2021 SDPWS Timber Shear Wall Design in RFEM 6
A walkthrough of light-frame timber shear wall design in RFEM 6 with the Multilayer Surfaces and Timber Design add-ons, built around a single wall modelled from scratch and later reworked with openings. The session covers how the framing, sheathing, and fastener connectors are defined together as one beam panel, how an FEA model captures the four sources of deflection named in SDPWS 2021 instead of approximating them, and how the members, the sheathing, and the connectors are each checked — member equations from NDS 2024, connector capacities from SDPWS 2021.
Presented by
Webinar language
English (US)Recommended skill level
Skills you will gain
- Build a timber shear wall from a single surface and let the beam panel thickness generate the studs, plates, and sheathing automatically
- Define the sheathing, framing, and fastener layout, then save the whole build-up as a template for later walls
- Trace the nonlinear nail-slip line hinge RFEM 6 generates back to the fastener slip provisions of the 2021 SDPWS
- Frame a wall around openings with surface cells, then restore the supports, hold-downs, and unbraced lengths
- Read the member, sheathing, and connector design ratios down to the NDS 2024 equations, variables, and code references behind them
This webinar includes
Webinar content
Amy Heilig introduces the session agenda, then breaks a timber shear wall into its parts: studs, top and bottom plates, sheathing, fasteners, and anchorage. The remainder frames the problem the webinar answers, covering the four sources of deflection named in SDPWS 2021, shear transfer ignored at openings, and black-box software results.
This segment covers the full modelling sequence: activating the multilayer surfaces and timber design add-ons, setting NDS 2024 and ASCE 7 in the base data, defining cross-sections and APA-derived sheathing materials, and building the wall as a beam panel. It closes with the nonlinear nail-slip line hinges checked against SDPWS 2021, supports, hold-downs, and loading.
With the wind load case calculated, the detailed model is displayed and the results are walked through: global deformation of sheathing and framing, in-plane shear stresses in the panels, member axial forces at the end posts, nodal and line support reactions, and the shear flow from the line hinge releases. It closes on why these differ from hand calculations.
Preparation for the code checks: effective lengths assigned to the vertical studs and the buckling modes that matter once sheathing braces them, a design support added so the bottom plate is checked for compression perpendicular to the grain, and the strength configuration whose beam panel tab governs connector design. The timber design add-on is then started.
The add-on results are reviewed layer by layer: design ratios for the members, with the NDS 2024 equations, adjustment factors, and code references behind each check, then the sheathing panels, then every sheathing-to-framing connector, where demand comes from the analysis and capacity from SDPWS 2021, including how thicknesses and spacings outside the code tables are treated.
Openings are cut into the wall surface, and a dedicated function regenerates the framing around them as surface cells, whose thickness can then be overwritten cell by cell to rotate a header. Supports, hold-downs, and effective lengths are reinstated, stress singularities at the opening corners are addressed, and the segment ends on platform framing and wall-to-wall connections with rigid links.
The opening list of software challenges is revisited as solutions, with each of the four SDPWS deflection sources now accounted for in the model. The close is a development roadmap: CSA O86 shear walls, SDPWS diaphragm design, horizontal blocking, gypsum materials, non-rectangular wall shapes, and automatic anchorage design through the Components add-on.
Who this webinar is for
- Engineers still sizing timber shear walls in spreadsheets because the dedicated software feels clunky and demands a complex workflow
- RFEM 6 users who need shear transfer above and below openings, and a view of the forces between the sheathing and the studs
- Engineers on a US project where deflection, members, sheathing, and connectors all have to be checked within one model
Application areas:
Industry:
Standards:
Role:
Product:
Webinars review
I would like to thank you for the webinar on "Torsional Warping (7 DOF)". It was one of the best webinars I have ever seen. Thanks to your clear explanations and illustrative examples, I finally understood several things that I had not fully understood before.
Ing. Aleš Kupča
Statika KUPAL s.r.o.
I really enjoyed the coaching course on dynamic analysis. … It was a good introduction to the seismic design. A particularly positive feature is the option to use the various tools used in the training by downloading a demo version during the training—that was a really good addition.
Karen L.
TÜV NORD Ensys GmbH & Co. KG
I am a student at the Technical University in Nuremberg and am currently working on my master's thesis using Dlubal Software (RSTAB). The coaching course on dynamics (EC 8) was very helpful for me. The course was conducted in an extremely professional manner.
Gleb Chernyshev
Germany
The Concrete Structures EC2 with RFEM 6 course content was very satisfactory and well-structured, making it easy to follow. … In short, the course is interesting and introductory—a perfect introduction to the topic.
M.Sc. V. Zinkevych
Obermeyer Holding GmbH
I would like to thank you for the opportunity to try out RFEM 6. … I would like to mention that I'm excited about how much information and webinars you share.
Ing. Ida Grünwaldová
Czech Republic
Was an excellent Webinar | 2018 NDS CLT Design in RFEM 6! Thank you.
Juan Alberto Tello Fuente
CUMBRA INGENIERIA
Due to your webinars and test versions, I started a new job as structural engineer on January 1, 2023. For this, I would like to thank you and your team.
Dipl.-Ing. Ayman Al Shouha
Germany
Unfortunately, I didn't have the opportunity to follow the live webinar, but due to your recording, which I've watched, I am very excited about the current possibilities of RFEM 6. … I was particularly impressed by the speaker!
Prof. Dr.-Ing. Henning Lungershausen
University of Applied Sciences, Trier
Thank you, the webinar "The Most Common User Errors with RFEM and RSTAB" was very informative!
Dipl.-Ing. Adam Balogh
ThyssenKrupp Industrial Solutions AG
I would like to thank you again for the very good webinar "Stability Analysis in Steel Structures with RFEM and RSTAB". In some points, I was able to get clarity and it helped me a lot. I will probably use this more often in the future.
Dipl.-Ing. Johann Mair
MÜHLBERG Beratende Ingenieure GmbH, Mühlberg + Mair Beratende Ingenieure GmbH
The "Soil-Structure Interaction in RFEM" webinar presentation was excellent and the topic was very interesting.
Prof. Lazaros Vasiliadis
Democritus Univestity of Thrace (DUTH)
The webinar "Design Cold-Formed Steel Sections According to EC3" was great. It was my first webinar and I would like to follow more in the future. Especially for new users/students like me and if too fast, it is very good that it is recorded and you can watch it again.
Veronika Klöck
Germany
Thank you for the webinar "Design Cold-Formed Steel Sections According to Eurocode 3." I really liked it. The webinar recordings are a real plus point. Continue to do so!
Bernd Jäckel
Gesellschaft für Planung und Vermessung mbH
I really enjoy watching the webinars you showcase on YouTube. They helped me to convince my client to recently purchase RFEM. They provide a wealth of information.
William Lefort, P.Eng.
Danwill Canada
I have watched the webinar recording "Design of Cross-Laminated Timber Panels (CLT) According to Eurocode 5" on YouTube, and I am impressed by the program and the very good presentation.
Dipl.-Ing. Lothar Reichle
Ingenieurbüro für Statik und Baukonstruktion
The webinar about RWIND Simulation was very successful! From now on, it is possible to analyze wind forces on geometries of objects that are not regulated in the standard. The wind force assumption according to the standard was often a more or less good estimate.
DI Dr. techn. Wolfgang Billensteiner
Civil Engineering Office DI Dr. Tech. Wolfgang Billensteiner
Your webinar on RWIND Simulation was very impressive. Like the speakers at the info days, the speaker confidently described the performance of the new program.
Ing. Johann Tauß
Austria
RSTAB is a software program that I recently discovered and which is very helpful for the calculation of steel structures. With the webinars available on the Dlubal website, I have familiarized myself with the various functions of the program.
Daisy Amila
Algeria
I watched the webinar "Dlubal Information Day Online 2014 – Part 2: RFEM 5 – Structural Analysis with Finite Elements for Concrete and Steel Structures" from 2014. It is a good and powerful video!
Dipl.-Ing. Thomas Steinkühler
Bojda Planungsgruppe
I've attended the webinar on glass design. Excellent explanation. I don't design glass structures; however, it was very interesting to explore the potential of the software.
Ing. Simone Luca Tanghetti
Studio Tanghetti
I've been using Dlubal's programs for most of my university studies. In the beginning, RFEM was far from being a mainstream software, so I didn't have many colleagues to advise me, but thanks to the well-designed controls and webinars, I quickly learned how to work with it.
Ing. Martin Závacký
Brno University of Technology
The webinar Timber Connection Design in RFEM and RSTAB was very successful! I am particularly pleased that you explained how to select the SFS intec dowel system WS-T. Thank you very much!
Caroline Göttlein
SFS intec
Instructors
Amy Heilig, PE
CEO – USA Subsidiary
Amy is the CEO of the U.S. subsidiary and is responsible for sales and continued program development for the North American market.
Alex Bacon, EIT
Support Engineer
Alex handles customer training and technical support for the North American market and works on continued program development.
Cisca Tjoa, PE
Senior Support Engineer
Cisca is the senior support engineer for the North American market, covering customer training, technical support, and program development.
Related Webinars
